Page 1 of 1

Tear drop turn signal housing disassembly

Posted: Sat Feb 22, 2020 5:04 pm
by GoldHawg
I'd like to send out my 69 tear drop turn signal housings to be rechromed, but I'm not sure whether or how to get the electrical part off. I do intend to go with LED lights in the end, so that may play in if I have to trash the electrical part. It appears like the electrical part (bottom of the housing is somehow just pressed in--doesn't look like the same material but I'm not sure. Thoughts?

Re: Tear drop turn signal housing disassembly

Posted: Sat Feb 22, 2020 8:23 pm
by Curtis
They are pressed in. You have to very carefully press or tap them out. If you would like a new pair of bodies I may have a set on the way here in a few hours. Would cost you about $65 or so plus shipping.

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 8:55 am
by CSP311
I haven't done the tear drop indicators, but my front indicators are similar in design. Remove bulb. Remove rear grommet, it probably lips under the metal (steel) end by gently levering out.. You may have to push some wire back through the grommet, this will push the bulb contact pad up. Undo the solder holding the pad. There is a spring. Picture is of my Silvia numberplate wiring, but the concept is the same.
You have an earth on the side, probably un-solder. The reardrop indicator is made of Zamak, my front indicators are zamak and the same steel, I just had them chromed as a whole unit.

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 11:14 am
by Pjackb
Check Yahoo Japan
you can get new housing for cheaper then re chroming these

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 2:36 pm
by GoldHawg
Pjackb wrote: Mon Feb 24, 2020 11:14 am Check Yahoo Japan
you can get new housing for cheaper then re chroming these
Any more specific hints? I went there but obviously even with the translation its not intuitively obvious how to find this. A link would be awesome!

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 7:02 pm
by Curtis
GoldHawg wrote: Mon Feb 24, 2020 2:36 pm
Pjackb wrote: Mon Feb 24, 2020 11:14 am Check Yahoo Japan
you can get new housing for cheaper then re chroming these
Any more specific hints? I went there but obviously even with the translation its not intuitively obvious how to find this. A link would be awesome!
Put in sp311. List them from high to low or reverse. They sell for 4000 yen. I just bought a set. You of course have to pay a bunch of fees to get them after you win them.

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 9:03 pm
by GoldHawg
I'd gladly buy at that price. Can't figure out how to go high to low, so I went thru every ad. There is a brand new set that goes for abut $585 NOS. I see a couple of ones worse than mine for 8000 yen:
https://page.auctions.yahoo.co.jp/jp/auction/q295683776

I don't see any new housings.

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 10:05 pm
by Pjackb
I just did a quick scan and couldn't find them, which mean the auction probably ended (they were some last week)
continue monitoring they will come back

Re: Tear drop turn signal housing disassembly

Posted: Mon Feb 24, 2020 10:12 pm
by Curtis
He sells a set and then lists another after a bit. I have bought several from him. If you want one I have on hand let me know.

Re: Tear drop turn signal housing disassembly

Posted: Tue Feb 25, 2020 6:50 am
by GoldHawg
Curtis wrote: Mon Feb 24, 2020 10:12 pm He sells a set and then lists another after a bit. I have bought several from him. If you want one I have on hand let me know.
You have PM.

Re: Tear drop turn signal housing disassembly

Posted: Tue Feb 25, 2020 8:15 am
by CSP311
Well, that is my lesson for today. I have whizzed pass the auction, not looking at these.

Here it is;

https://page.auctions.yahoo.co.jp/jp/auction/s720029330